H-ZX32-3FH

Cutaway view of the SunStar ZX32 3F tanning bed
SunStar ZX32 tanning bed ballast tray

This SUNSTAR® ZX32 3FSPEED® 175 system was shipped with the following lamps:
SPEED® 175 Wolff® Model SPD75-T12 Bi-Pin
Philips® Model HPA 400/30s or CosmoTech® Model 23045 or 20046(facial unit)

Sort by: sort_asc     Display #  
<< << Start << Prev 1 2 3 Next >> End >> >>

Results 1-20 of 51

Product List

10070|Contactor (240VAC, 30A)

Tanning bed control contactor rated for 30 Amps on 240VAC service.
[Product Details...]

10072|Contactor (240VAC, 40A)

Tanning bed control contactor rated for 40 Amps on 240VAC service.
[Product Details...]

10081|Fan, 4" (220VAC, 110cfm)

Square fan, measures approximately 4" on a side, used for general cooling of tanning bed.
[Product Details...]

10541|Wiring Harness, Keypad to Timer

This is the wiring harness that runs from the tanning bed timer to the keypad in the head-end endcap.
[Product Details...]

10894|Trim Profile, Gray (Full Length)

Full-length gray colored strip that secures the long edges of the tanning bed cover.
[Product Details...]

10895|Trim Profile, Canopy Rear Middle (Gray)

Gray colored strip that secures the back edge of the tanning bed canopy cover.
[Product Details...]

10896|Trim Profile, Canopy Rear Ends (Gray)

Gray colored strip that secures the back edge of the tanning bed canopy cover.
[Product Details...]

10902|Cover, Bench Grey (Power Near Foot-end)

Bench cover for SunStar® and Sunvision Elite™ commercial tanning beds
[Product Details...]

10929|Cover, Canopy Blue (w/ Face Tanner)

Dark blue, contoured canopy cover for SunStar® commercial tanning beds, logo decal included
[Product Details...]

10932|Silk-Screened Profile (H/J-ZX32-3F)

Plastic side profile with tanning bed logo and warning wording required by FDA for tanning beds.
[Product Details...]

16610|Wiring Harness, Resistor Code

The resistor code harness is a device that tells the timer what type of tanning bed it is installed in
[Product Details...]

20063|Capacitor, 75µF

75µF capacitor used for power factor correction
[Product Details...]

20080|Lamp Holder w/o Starter Holder

Lamp holder for BI-PIN fluorescent tanning lamps. Does not have holder for starters.
[Product Details...]

20081|Lamp Holder w/ Starter Holder

Lamp holder for BI-PIN fluorescent tanning lamps. Includes holder for starters.
[Product Details...]

20127|Snap Rivet (for fan grill)

White plastic rivet that holds 4" wire fan grill in place
[Product Details...]

20135|Grill, Fan 4" Wire

4" wire fan grill. Keeps fingers and large debris out of fan blades.
[Product Details...]

20193|Hour Counter

Electro-mechanical hour counter for tanning beds. Keeps track of time the tanning bed is in use.
[Product Details...]

20210|Lamp Holder, Face Tanner (HPFT)

Porcelain spring-type lamp holder socket for face tanner lamp. One side only. Two required to hold lamp.
[Product Details...]

20317|Foot Cap

Plastic cap on the bottom of each stand leg of SunStar® commercial tanning beds
[Product Details...]

20592|Relay (220VAC, 15A)

15A contact relay, usually used to activate cooling fans in tanning beds
[Product Details...]

Contraindication: This product is contraindicated for use on persons under the age of 18 years. "Contraindication: This product must not be used if skin lesions or open wounds are present." "Warning: This product should not be used on individuals who have had skin cancer or have a family history of skin cancer." "Warning: Persons repeatedly exposed to UV radiation should be regularly evaluated for skin cancer.

Information about cookies

This site uses cookies. By using the website and its offers and continuing to navigate, you accept these cookies. You can change this in your browser settings. More Information